The target selection of the first few observational runs in the northern hemisphere heavily relied on Strömgren photometry. The aim is a detailed inventory of the neutron-capture elements. The project Measuring at Intermediate metallicity Neutron Capture Elements (MINCE) (Cescutti et al., in prep.) has the goal of obtaining chemical abundances for stars in the intermediate metallicity range (− 2.5 ≤ ≤ − 1).
Midas gen 2017 license#
Open Access article, published by EDP Sciences, under the terms of the Creative Commons Attribution License ( ), which permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. The observed rotational velocities are in line with theoretical predictions of the evolution of rotating stars. All but one of the sample stars present low and high ratios together with constant, suggesting that they have undergone CNO processing and first dredge-up. All stars are in prograde motion around the Galactic centre and belong to the thin-disc population. We identify 15 stars as likely binary stars. The age-metallicity degeneracy can affect photometric metallicity calibrations. We used spectrum synthesis and model atmospheres to determine chemical abundances for 16 elements (C, N, O, Mg, Al, Ca, Fe, Sr, Y, Ba, La, Ce, Pr, Nd, Sm, and Eu) and rotational velocities. These masses, together with Gaia photometry and parallaxes, were used to derive the stellar parameters. Stellar masses were derived by comparison of the position of the stars in the colour-magnitude diagram with theoretical evolutionary tracks. These stars where of spectral type A to B when on the main sequence, and we therefore wished to compare their abundance pattern to that of main-sequence A and B stars. We determined the chemical composition and rotational velocities of these stars in order to compare them with predictions from stellar evolution models. In the search of a sample of metal-poor bright giants using Strömgren photometry, we serendipitously found a sample of 26 young (ages younger than 1 Gyr) metal-rich giants, some of which have high rotational velocities.Īims.
INAF – Osservatorio di Astrofisica e Scienza dello Spazio di Bologna, Via Gobetti 93/3, 40129 Bologna, ItalyĬontext. Valerio 2, 34127 Trieste, Italyĭipartimento di Fisica e Astronomia, Università degli Studi di Bologna, Via Gobetti 93/2, 40129 Bologna, Italy IFPU, Istitute for the Fundamental Physics of the Universe, Via Beirut, 2, 34151 Grignano, Trieste, Italy INAF, Osservatorio Astronomico di Trieste, Via Tiepolo 11, 34143 Trieste, Italy IRAP, CNRS UMR 5277 and Université de Toulouse, 14 Avenue Edouard Belin, 31400 Toulouse, Franceĭepartamento de Ciencias Fisicas, Universidad Andres Bello, Fernandez Concha 700, Las Condes, Santiago, Chile GEPI, Observatoire de Paris, Université PSL, CNRS, 5 place Jules Janssen, 92195 Meudon, FranceĮ-mail: of Astronomy, University of Geneva, Chemin PegVersoix, Switzerland Linda Lombardo 1, Patrick François 1, Piercarlo Bonifacio 1, Elisabetta Caffau 1, Aroa del Mar Matas Pinto 1, Corinne Charbonnel 2 ,3, Georges Meynet 2, Lorenzo Monaco 4, Gabriele Cescutti 5 ,6 ,7 and Alessio Mucciarelli 8 ,9
If yes, please also check your exact name of Revit you are using and inform us. Please check if student version allows “Adds-in” module. However, we have not tested student version.
Midas gen 2017 trial#
We have checked MIDAS-Revit link for both commercial version and trial version and it worked without any problem. This link works as “Adds-in” module in Revit program. Yours sincerely, Answer:Hi, MIDAS-Revit link supports Revit, Revit Structure, and Revit Architecture. As I have Student Version, I wonder if that is the reason why Midas Link cannot use it. When I accept, I get a new message Midas Link for Revit 2017 Error 1001, Installation was cancelled I underlined the sentence "that can use Midas Link" because I have Revit 2017 installed, so I think I may have a Revit that Midas Link cannot use.
Midas gen 2017 install#
Please install Revit 2017 first and try again. Midas Link for Revit 2017 Any version of Revit that can use Midas Link has not yet been installed on your computer. I try to install Midas Gen Link For Revit 2017, using the files MidasLinkSetupForRevit2017.msi or setup.exe in C:\Program Files\MIDAS\midas Gen\midas link for Revit Structure\Revit 2017 MidasLink_for64bitPC However, I get an error message. Question: Dear Sir or Madam, I have installed Revit 2017 Student Version.